| The HydroStar Parts Kit. |
| What is it? |
| The HydroStar Parts Kit is a boxed kit of all the parts to build the HydroStar Generator. All you will have to do is put the parts together as the instructions tell you to do. It is as easy as one, two, and three. |
| What do the parts consist of? |
| Good Question! The parts in the HydroStar Parts Kit are as follows: 1. One peace of schedule 80 CPVC Pipe, 17 inches long that has been threaded on both ends and bored out on one end to allow the toroid coil to fit inside. See picture below. 2. One T304 Stainless Steel Tube that is 12 inches long and has an outside diameter of 3.5 inches. The thickness of the stainless steel tube is .065. This is one of the electrodes. See picture below. 3. Another T304 Stainless Steel Tube that is also 12 inches long but has an outside diameter of 3.25 inches. This tube will be placed inside of the 3.5 outside diameter tube above. It's thickness is the same as the above tube which is .065. This is the second electrode. See picture below. 4. A Toroid Coil that has been wound 2000 times around a 3.5 toroid core that has a inner diameter of 2 inches. See picture below. 5. Two schedule 80 PVC threaded end caps that fit on each end of the schedule 80 PVC Pipe. See picture below. 6. An electronic stainless steel float that lets the water pump know when to replace the water in the chamber of the HydroStar Housing. See picture below. 7. One each check valve to let the water into the chamber of the HydroStar Housing when the water pump is turned on by the electronic stainless steel float. See picture below. 8. A 1&1/2 inch PVC schedule 80 pipe that is used as a swash plate around the electronic stainless steel float. The pipe is 4 inches long. See picture below. 9. One each one inch thick solid PVC schedule 80 bar. This is used to mount the electronic stainless steel float and secure the wiring from it to the top of the PVC threaded cap. See picture below. 10. Two PVC disks that will fit inside one end of each of the electrodes. 11. One each pressure relief valve that is set at 85 psi. See picture below. 12. One each drain plug. This lets you drain all the water out of the HydroStar Generator Housing. See picture below. 13. One each hose barbed fitting. This is the fitting that lets the hydrogen & oxygen out of the HydroStar Generator Housing to the flam arrestor and from there to the intake manifold. See picture below. 14. One each pressure gauge. To monitor the pressure inside the HydroStar Generator Housing. See picture below. |
| Below is a picture of all the parts of the HydroStar Parts Kit. After this picture are pictures of the individual parts. |
| Below is item #1 from the above list of parts. One piece of schedule 80 PVC Pipe, 17 inches long that has been threaded on both ends and bored out on one end to allow the toroid coil to fit inside. |
| Below is items #2 & #3 from the above list of parts. One T304 Stainless Steel Tube that is 12 inches long and has an outside diameter of 3.5 inches. The thickness of the stainless steel tube is .065. This is one of the electrodes. Also shown is item #3. Another T304 Stainless Steel Tube that is also 12 inches long but has an outside diameter of 3.25 inches. This tube will be placed inside of the 3.5 outside diameter tube. It's thickness is also .065. This is the second electrode. Notice the holes at the top of the tubes. The small holes hold the PVC disk in place. The larger holes let water into both tubes. You will have to drill your on holes and tig weld the welding rods into place as shown in the HydroStar Manual. |
| Below is item #4 from the parts list above. A Toroid Coil that has been wound 2000 times around a 3.5 toroid core that has an inner diameter of 2 inches. |
| Below is item #5 from the parts list above. Two schedule 80 PVC threaded end caps that fit on each end of the schedule 80 PVC Pipe. |
| Below is item #6 from the parts list above. An electronic stainless steel float that lets the water pump know when to replace the water in the chamber of the HydroStar Housing. |
| Below is item #7 from the parts list above. One each check valve to let the water into the chamber of the HydroStar Housing when the water pump is turned on by the electronic stainless steel float. |
| Below is item #8 from the parts list above. A 1&1/2 inch PVC schedule 80 pipe that is used as a swash plate around electronic stainless steel float. The pipe is 4 inches long. |
| Below is item #9 from the parts list above. One each, one inch thick, solid PVC schedule 80 bar. This is used to mount the electronic stainless steel float and secure the wiring from it to the top PVC threaded cap. |
| Below is item #10 from the parts list above. Two PVC disks that will fit inside one end of each of the electrodes. |
| Below is item #11 from the parts list above. One each pressure relief valve that is set at 85 psi. |
| Below is item #12 from the parts list above. One each drain plug. This lets you drain all the water out of the HydroStar Generator Housing. Mounted on the bottom threaded end cap. |
| Below is item #13 from the parts list above. One each hose barbed fitting. This is the fitting that lets the hydrogen & oxygen out of the HydroStar Generator Housing to the flam arrestor and from there to the intake manifold. |
| Below is item #13 from the parts list above. One each pressure gauge. To monitor the pressure inside the HydroStar Generator Housing. |
| What is the warranty on the HydroStar Kit? |
The HydroStar Kit is warranted to have the parts needed to build the HydroStar
Generator as instructed in the manual. The parts meet or exceed what the HydroStar
Manual calls for. There has been some revision as to construction of the parts and this
is reflected in the instructions on how to construct the HydroStar Generator. You will
receive all the parts as listed above, a parts list, written instructions on how to construct
the HydroStar Generator. There are no other written or implied warranties. All sales are
final.
Generator as instructed in the manual. The parts meet or exceed what the HydroStar
Manual calls for. There has been some revision as to construction of the parts and this
is reflected in the instructions on how to construct the HydroStar Generator. You will
receive all the parts as listed above, a parts list, written instructions on how to construct
the HydroStar Generator. There are no other written or implied warranties. All sales are
final.
| How long does it take to get the HydroStar Generator kit? |
| What other parts are need to build the HydroStar System? |
The HydroStar System involves more than the Hydrogen Generator. Even though
the HydroStar Generator is the hardest and most expensive part to build you will
still need other items. You will need to build the In-Dash Indicators Circuit found on
page 17 of the HydroStar Manual. This is only if you want gauges inside of your
car. No matter what, do build the circuit for the water pump. You will need a water
pump and water tank. If you do not build the circuit for the water pump you stand
the risk of burning out the generator water level sensor. Do not connect the
generator water level sensor straight to the pump and battery. You will burn the
sensor up.
We will be coming out with a kit for the flame arrestor. I will keep you informed.
You will need the different hoses to connect the hydrogen generator to the intake
manifold, the water tank to the pump and then to the hydrogen generator. All of
this is in the HydroStar Manual and tells you what and where to purchase these
items. If you do not have the HydroStar Manual, get that first and read it so you will
know what you are getting into and how to put the parts kit together. The manual
does not come with the parts kit. The only instructions in the HydroStar Parts Kit is
the changes from the manual of construction. There are short cuts to the
construction, which I show you that comes with the parts kit. You can get the
manual at: http://www.wam-a-bam.com. Just click on the "Buy Now" button at the
bottom of the web page. Click on the "Buy Now" button on the right so that you
can get the UltraMist Manual as well.
The hy-tronics is the electronics that control the HydroStar Generator. You need
this as it is the heart of the system. Go to: http://www.restarmodule.com for the
board and parts list of the hy-tronics. They have revised the electronics from what
is in the manual. They have it working right!
If you have a fuel injection engine, you will need an O2 sensor and Map sensor
enhancers. You can find these by going to e-bay.com and typing in their search
box "O2 sensor enhancer and map sensor enhancer". What these sensors do is
blind the computer as to if the engine is burning too lean or rich. With out these
sensors, the system will not work!
Also, you will need the UltraMist Vapor Injector to keep the engine cool and slow
down the burning of the hydrogen. This address's the pre-ignition problem that
you may encounter. It is easy and inexpensive to build. You can get the
instructions on how to build the Vapor Injector by clicking on:
http://www.wam-a-bam.com/UltraMist.
the HydroStar Generator is the hardest and most expensive part to build you will
still need other items. You will need to build the In-Dash Indicators Circuit found on
page 17 of the HydroStar Manual. This is only if you want gauges inside of your
car. No matter what, do build the circuit for the water pump. You will need a water
pump and water tank. If you do not build the circuit for the water pump you stand
the risk of burning out the generator water level sensor. Do not connect the
generator water level sensor straight to the pump and battery. You will burn the
sensor up.
We will be coming out with a kit for the flame arrestor. I will keep you informed.
You will need the different hoses to connect the hydrogen generator to the intake
manifold, the water tank to the pump and then to the hydrogen generator. All of
this is in the HydroStar Manual and tells you what and where to purchase these
items. If you do not have the HydroStar Manual, get that first and read it so you will
know what you are getting into and how to put the parts kit together. The manual
does not come with the parts kit. The only instructions in the HydroStar Parts Kit is
the changes from the manual of construction. There are short cuts to the
construction, which I show you that comes with the parts kit. You can get the
manual at: http://www.wam-a-bam.com. Just click on the "Buy Now" button at the
bottom of the web page. Click on the "Buy Now" button on the right so that you
can get the UltraMist Manual as well.
The hy-tronics is the electronics that control the HydroStar Generator. You need
this as it is the heart of the system. Go to: http://www.restarmodule.com for the
board and parts list of the hy-tronics. They have revised the electronics from what
is in the manual. They have it working right!
If you have a fuel injection engine, you will need an O2 sensor and Map sensor
enhancers. You can find these by going to e-bay.com and typing in their search
box "O2 sensor enhancer and map sensor enhancer". What these sensors do is
blind the computer as to if the engine is burning too lean or rich. With out these
sensors, the system will not work!
Also, you will need the UltraMist Vapor Injector to keep the engine cool and slow
down the burning of the hydrogen. This address's the pre-ignition problem that
you may encounter. It is easy and inexpensive to build. You can get the
instructions on how to build the Vapor Injector by clicking on:
http://www.wam-a-bam.com/UltraMist.
| Understanding the HydroStar System. |
The HydroStar Manual is designed to run on water only with the ability to switch back
over to gasoline. However, the man that wrote the manual must have lied to us because
the Hytronics, as he calls it, does not produce enough volume of hydrogen and oxygen to
run an engine on water only. You need eight liters per minute of hydrogen and oxygen to
run an average eight cylinder engine on water. So, what we ended up with is a glorified
hydrogen booster. This is when we use the hydrogen generator of the HydroStar System
along with gasoline/diesel to produce more miles per gallon. The HydroStar System
works quite well in this capacity. We have found that we can take 4.5 liter engine that is
getting 18 miles per gallon (MPG) and increase that MPG to around 53 MPG. There is a
guy in Alabama that took his wife's car, a Toyota, from 25 MPG to 73 MPG. To get this
kind of mileage increase you not only need the HydroStar Generator, you use the
UltraMist Vapor Injector ( CLICK HERE to get more information on the UltraMist Vapor
Injector). You may need a oxygen sensor enhancer, a MAP sensor enhancer, and the Gas
Blaster. You can get more information about the Gas Blaster by clicking on the following
link: http://www.the-gas-saver-connection.com. I highly recommend the Gas Blaster! You
can find the oxygen sensor enhancers and the MAP sensor enhancers on the Internet.
Just type their names in your search engine of your computers or go to: www.ebay.com
and type into their search box either MAP sensor enhancer or oxygen sensor enhancer.
There are many Hydrogen Boosters out there on the Internet but none that can offer the
hydrogen output that the HydroStar does. The HydroStar system is more expensive to
build than most hydrogen boosters, but, keep in mine, the HydroStar Generator is built to
where you can attach the Hytronics to it very easy. The Hytronics are being redesign.
Once it comes out and has been tested, all you will have to do is attach it to the
HydroStar Generator and then you will be able to run your car on water only. The
electronics, that will let you run on water only, are being redesign by man who is retired
from Lockheed Martin. He designed circuit broads for missiles for the Defense
Department. He taught electronics. He feels certain that he can do this. He has all the
patents that Stanly Meyers filed with the US Patent Office. He has studied these patents
and feels sure he can duplicate them. We will see. Until then, the HydroStar System is
one of the top hydrogen generators that works as a very good hydrogen booster and the
above parts will help you build it.
over to gasoline. However, the man that wrote the manual must have lied to us because
the Hytronics, as he calls it, does not produce enough volume of hydrogen and oxygen to
run an engine on water only. You need eight liters per minute of hydrogen and oxygen to
run an average eight cylinder engine on water. So, what we ended up with is a glorified
hydrogen booster. This is when we use the hydrogen generator of the HydroStar System
along with gasoline/diesel to produce more miles per gallon. The HydroStar System
works quite well in this capacity. We have found that we can take 4.5 liter engine that is
getting 18 miles per gallon (MPG) and increase that MPG to around 53 MPG. There is a
guy in Alabama that took his wife's car, a Toyota, from 25 MPG to 73 MPG. To get this
kind of mileage increase you not only need the HydroStar Generator, you use the
UltraMist Vapor Injector ( CLICK HERE to get more information on the UltraMist Vapor
Injector). You may need a oxygen sensor enhancer, a MAP sensor enhancer, and the Gas
Blaster. You can get more information about the Gas Blaster by clicking on the following
link: http://www.the-gas-saver-connection.com. I highly recommend the Gas Blaster! You
can find the oxygen sensor enhancers and the MAP sensor enhancers on the Internet.
Just type their names in your search engine of your computers or go to: www.ebay.com
and type into their search box either MAP sensor enhancer or oxygen sensor enhancer.
There are many Hydrogen Boosters out there on the Internet but none that can offer the
hydrogen output that the HydroStar does. The HydroStar system is more expensive to
build than most hydrogen boosters, but, keep in mine, the HydroStar Generator is built to
where you can attach the Hytronics to it very easy. The Hytronics are being redesign.
Once it comes out and has been tested, all you will have to do is attach it to the
HydroStar Generator and then you will be able to run your car on water only. The
electronics, that will let you run on water only, are being redesign by man who is retired
from Lockheed Martin. He designed circuit broads for missiles for the Defense
Department. He taught electronics. He feels certain that he can do this. He has all the
patents that Stanly Meyers filed with the US Patent Office. He has studied these patents
and feels sure he can duplicate them. We will see. Until then, the HydroStar System is
one of the top hydrogen generators that works as a very good hydrogen booster and the
above parts will help you build it.
This will depend on any back log of parts that I will need from the manufactures and the back
log of sales that I have at any given time. It could be any where from one month to four
months. I will keep you informed as to the time I think it will take to get the kit out to you after
your purchase. I will do everything in my power to get the kits to you as soon as possible. If
you need to contact me you may do so by e-mail at: admin@wam-a-bam.com or call me at:
281-488-3955. If you do not know my name by now it is: Donald Harper. My address is: 922
Redway, Houston, TX 77062.
log of sales that I have at any given time. It could be any where from one month to four
months. I will keep you informed as to the time I think it will take to get the kit out to you after
your purchase. I will do everything in my power to get the kits to you as soon as possible. If
you need to contact me you may do so by e-mail at: admin@wam-a-bam.com or call me at:
281-488-3955. If you do not know my name by now it is: Donald Harper. My address is: 922
Redway, Houston, TX 77062.
| What is my investment and how do I purchase the HydroStar Generator Kit? |
As I said before, the HydroStar Generator is more expensive than most hydrogen
generators. It is not made out of cheap material. You are talking Industrial Strength here.
Also, it is designed so that when the Hytronics are built and tested, all you will need to
do is attach and/or reroute some wires and change the location as to where the
hydrogen fuel is directed. When this is done, you can run straight on water for fuel. No
gasoline will be needed except to switch over to gasoline for 10 minutes or so to burn
out the water left behind in your engine and exhaust system. Also, being able to switch
back over to gasoline gives you two fuel sources. For now, I reccomend using the
Hy-tronics that is offered at: http://www.restarmodule.com.
So, Whats the cost? Your investment to purchase the HydroStar Generator Kit is
$995.00 plus shipping and handling. Your shipping and handling is $66.00 if you live in
the United States. If you live in Canada, your cost is: $92.00. All other countries out side
of the U.S. And Canada, your investment for shipping and handling is: $130.00. The
reason for the extra cost for those of you that live out side of the U.S. Is because I have
to mail your kit by express mail. This is the only way I can get a tracking number from
the U.S. Postal Service. I just can not afford to lose any kits in the mail.
generators. It is not made out of cheap material. You are talking Industrial Strength here.
Also, it is designed so that when the Hytronics are built and tested, all you will need to
do is attach and/or reroute some wires and change the location as to where the
hydrogen fuel is directed. When this is done, you can run straight on water for fuel. No
gasoline will be needed except to switch over to gasoline for 10 minutes or so to burn
out the water left behind in your engine and exhaust system. Also, being able to switch
back over to gasoline gives you two fuel sources. For now, I reccomend using the
Hy-tronics that is offered at: http://www.restarmodule.com.
So, Whats the cost? Your investment to purchase the HydroStar Generator Kit is
$995.00 plus shipping and handling. Your shipping and handling is $66.00 if you live in
the United States. If you live in Canada, your cost is: $92.00. All other countries out side
of the U.S. And Canada, your investment for shipping and handling is: $130.00. The
reason for the extra cost for those of you that live out side of the U.S. Is because I have
to mail your kit by express mail. This is the only way I can get a tracking number from
the U.S. Postal Service. I just can not afford to lose any kits in the mail.
| To order the HydroStar Generator Kit and you live in the United States, click on the "Buy Now" button below |
| To order the HydroStar Generator Kit and you live in Canada, click on the "Buy Now" button below. |
| To order the HydroStar Generator Kit and you live out side of the United States and Canada, click on the "Buy Now" button below. |