| The Completed HydroStar Generator already put together for you. |
For you people that just don't want to fool around and buy all
the parts and put the HydroStar Generator together, this is the
perfect solution. Purchase the unit already made for you. All
you have to do now is get the electronics for the unit, known
as the Hy-tronics in the manual, and the O2 sensor enhancer to
install the units on to your engine as an attachment to the
engine. You can purchase the Hy-tronics at:
http://www.wam-a-bam.com/Hy-tronics. You can also get the
O2 sensor enhancer at:
http://www.replacewaterforfuel.com/Elktrktb_O2Sensor
Also, I recommend that you install the Ultra*Mist Vapor
injector. This will also increase your miles per gallon and aid
in keeping the engine temperature in operating range. It is so
easy to build and will cost you no more that $30.00 to build it.
You can get the manual on how to build it by clicking on:
http://www.wam-a-bam.com/UltraMist.
The above picture of the Hydro*Star Generator does not show
the coil wires that will protrude out of the side of the cylinder
close to the top, just below the top threads. About were the (r)
is on the word Star. There will be two wires sticking out and
they are to be connected to the Hy-tronics.
The HydroStar Generator is made as shown in the Hydro*Star
Manual. I highly suggest that you get your free copy of the
Hydro*Star manual so you can see whats going on inside the
generator and how it was put together. You can get the
HydroStar Manual by clicking on the FREE button below.
the parts and put the HydroStar Generator together, this is the
perfect solution. Purchase the unit already made for you. All
you have to do now is get the electronics for the unit, known
as the Hy-tronics in the manual, and the O2 sensor enhancer to
install the units on to your engine as an attachment to the
engine. You can purchase the Hy-tronics at:
http://www.wam-a-bam.com/Hy-tronics. You can also get the
O2 sensor enhancer at:
http://www.replacewaterforfuel.com/Elktrktb_O2Sensor
Also, I recommend that you install the Ultra*Mist Vapor
injector. This will also increase your miles per gallon and aid
in keeping the engine temperature in operating range. It is so
easy to build and will cost you no more that $30.00 to build it.
You can get the manual on how to build it by clicking on:
http://www.wam-a-bam.com/UltraMist.
The above picture of the Hydro*Star Generator does not show
the coil wires that will protrude out of the side of the cylinder
close to the top, just below the top threads. About were the (r)
is on the word Star. There will be two wires sticking out and
they are to be connected to the Hy-tronics.
The HydroStar Generator is made as shown in the Hydro*Star
Manual. I highly suggest that you get your free copy of the
Hydro*Star manual so you can see whats going on inside the
generator and how it was put together. You can get the
HydroStar Manual by clicking on the FREE button below.
| What am I looking at in the above photo of the HydroStar Generator? |
As you look at the photo of the HydroStar Generator you will
notice a red cap at the top of the generator that is screwed onto
the white shaft of the generator. This cap has a black hose that
is connected to a pressure gage. You may want to put this gage
on your dish board as it measures the pressure inside of the
Hydrogen Generator. However, you won't see much pressure
unless the outlet of the hydrogen gas gets block off. That way
we install a pressure relief value. If you do decide to place the
pressure gage on your dash board you will need a longer hose.
Also, you will see a black hose that is coming out of the top of
the cap with a white tube connected to it. This is were the
hydrogen & oxygen, that is produced inside the generator,
comes out to your intake manifold. The white tube is the flash
arrestor. The flash arrestor is a safety device that stops any
flame from a back fire of the engine entering the hydrogen
generator and causing an explosion.
Also, you will notice on the top of the red cap that there are two
red wires protruding from the top of the cap. These wires are to
be connected to the electronics that will control the water
pump. The water pump and water tank is one of the things that
you will need to purchase. You can use any size water tank but
I recommend that you get at least a five gallon tank. The
Hydro*Star manual will tell you were to order the water pump or
you can order it from me. What ever you do, do not connect the
water pump directly to the battery. This will burn out the level
switch in the Hydrogen Generator that tells the pump to turn
on once the water gets low in the generator. So, do not connect
these wires directly to the battery. Wire these wires to the
electronics (Hy-Tronics) of the system. Click HERE for more
details about the Hy-Tronics.
You will also see a metal pressure relief vale on top of the red
cap of the Hydro*Star Generator. This is for relieving pressure
inside of the generator if pressure gets above 85 PSI. So, you
have two safety devices on the Hydro*Star Generator. One
being the flash arrestor and the other being the pressure relief
value. This makes the Hydro*Star Generator safe to operate.
As you look down the white shaft of the generator you will see
a black hose sticking out of the side of the shaft. This is a
check value that lets the water into the generator when the
float value tells the water pump to replace depleted water. It is
tied into the water pump and the water tank.
The bottom red cap of the Hydro*Star Generator is were the
electrodes are connected. The outer electrode, that protrudes
with a bolt and screw nut, is the (+) positive connection. The
inner electrode is the (-) negative connection, which has a bolt
and screw nut next to the (+) positive electrode, and is in close
proximity of the (+) positive connection electrode. You will find
another bolt and nut protruding on the other side of the end
cap. This is to secure the positive electrode to the end cap.
The inner electrode that is inserted into the outer electrode has
a nylon spacer between them. This keeps the two electrodes
from shorting out.
You will also see a drain plug on the end cap of the HydroStar
Generator. This is to be used as a way to drain the water out of
the HydroStar Generator for maintenance.
You should use distilled water with 1/2 to 1 teaspoon of baking
soda or lye (Patassuem Hydroxcide) for each gallon of water in
your Hydro*Star Generator. You can increase the amount of
baking soda or lye if you don't see enough production of
hydrogen and oxygen of the Hydro*Star Generator. Please
understand that an increase of baking soda or lye will increase
the amount amperage that is pulled from the battery. The
weight of the Hydro*Star Generator is about 17 lbs. It stands
about 23" inches tall. This includes the protruding drain plug
and electrodes on the bottom cap and the protruding
connections on the top cap. With the caps, the width of the
tube is 5.5" inches wide. The generator always stands
vertically. You may have to place the unit in your trunk
standing straight up.
notice a red cap at the top of the generator that is screwed onto
the white shaft of the generator. This cap has a black hose that
is connected to a pressure gage. You may want to put this gage
on your dish board as it measures the pressure inside of the
Hydrogen Generator. However, you won't see much pressure
unless the outlet of the hydrogen gas gets block off. That way
we install a pressure relief value. If you do decide to place the
pressure gage on your dash board you will need a longer hose.
Also, you will see a black hose that is coming out of the top of
the cap with a white tube connected to it. This is were the
hydrogen & oxygen, that is produced inside the generator,
comes out to your intake manifold. The white tube is the flash
arrestor. The flash arrestor is a safety device that stops any
flame from a back fire of the engine entering the hydrogen
generator and causing an explosion.
Also, you will notice on the top of the red cap that there are two
red wires protruding from the top of the cap. These wires are to
be connected to the electronics that will control the water
pump. The water pump and water tank is one of the things that
you will need to purchase. You can use any size water tank but
I recommend that you get at least a five gallon tank. The
Hydro*Star manual will tell you were to order the water pump or
you can order it from me. What ever you do, do not connect the
water pump directly to the battery. This will burn out the level
switch in the Hydrogen Generator that tells the pump to turn
on once the water gets low in the generator. So, do not connect
these wires directly to the battery. Wire these wires to the
electronics (Hy-Tronics) of the system. Click HERE for more
details about the Hy-Tronics.
You will also see a metal pressure relief vale on top of the red
cap of the Hydro*Star Generator. This is for relieving pressure
inside of the generator if pressure gets above 85 PSI. So, you
have two safety devices on the Hydro*Star Generator. One
being the flash arrestor and the other being the pressure relief
value. This makes the Hydro*Star Generator safe to operate.
As you look down the white shaft of the generator you will see
a black hose sticking out of the side of the shaft. This is a
check value that lets the water into the generator when the
float value tells the water pump to replace depleted water. It is
tied into the water pump and the water tank.
The bottom red cap of the Hydro*Star Generator is were the
electrodes are connected. The outer electrode, that protrudes
with a bolt and screw nut, is the (+) positive connection. The
inner electrode is the (-) negative connection, which has a bolt
and screw nut next to the (+) positive electrode, and is in close
proximity of the (+) positive connection electrode. You will find
another bolt and nut protruding on the other side of the end
cap. This is to secure the positive electrode to the end cap.
The inner electrode that is inserted into the outer electrode has
a nylon spacer between them. This keeps the two electrodes
from shorting out.
You will also see a drain plug on the end cap of the HydroStar
Generator. This is to be used as a way to drain the water out of
the HydroStar Generator for maintenance.
You should use distilled water with 1/2 to 1 teaspoon of baking
soda or lye (Patassuem Hydroxcide) for each gallon of water in
your Hydro*Star Generator. You can increase the amount of
baking soda or lye if you don't see enough production of
hydrogen and oxygen of the Hydro*Star Generator. Please
understand that an increase of baking soda or lye will increase
the amount amperage that is pulled from the battery. The
weight of the Hydro*Star Generator is about 17 lbs. It stands
about 23" inches tall. This includes the protruding drain plug
and electrodes on the bottom cap and the protruding
connections on the top cap. With the caps, the width of the
tube is 5.5" inches wide. The generator always stands
vertically. You may have to place the unit in your trunk
standing straight up.
| O.K. What's the price for the HydroStar System. |
OK. Good question!! Understand that the Hydro*Star
Generator is made of industrial strength material. It is made to
last and to give you the most amount of volume of Hydrogen
& Oxygen than most generators. The amount of volume is
directly dependent on the electronics that you use. The best
type of electronics to use is the Hy-tronics shown in the
manual. There are also pulse generators of different types. But
you can not use a direct connection to the battery. You could
damage your alternator and your battery. I suggest that you
get your electronics (Hy-Tronics and O2 sensor enhancer) at
http://www.wam-a-bam.com/Hy-tronics
The investment for the Hydro*Star Generator is $1,190.00 plus
shipping and handling. If you live in the United States the
shipping and handling is $80.00. If you live in Canada, your
shipping is $100.00. All other country's shipping and handling
will be $150.00. I use Paypal.com to process credit cards and
electronic checks. If you do not like doing that, you can send
me a check or money order for the amount of purchase. Checks
will take at least 7 working days to clear before I can process
your order. Make all checks or money orders out to (Donald
Harper). Send checks or money orders to: Donald Harper, 922
Redway, Houston, TX 77062. For credit card or electronic
check purchase, click on the appropriate (Buy Now) buttons
below.
For U.S purchase | For Canada purchase | For other countrys
Generator is made of industrial strength material. It is made to
last and to give you the most amount of volume of Hydrogen
& Oxygen than most generators. The amount of volume is
directly dependent on the electronics that you use. The best
type of electronics to use is the Hy-tronics shown in the
manual. There are also pulse generators of different types. But
you can not use a direct connection to the battery. You could
damage your alternator and your battery. I suggest that you
get your electronics (Hy-Tronics and O2 sensor enhancer) at
http://www.wam-a-bam.com/Hy-tronics
The investment for the Hydro*Star Generator is $1,190.00 plus
shipping and handling. If you live in the United States the
shipping and handling is $80.00. If you live in Canada, your
shipping is $100.00. All other country's shipping and handling
will be $150.00. I use Paypal.com to process credit cards and
electronic checks. If you do not like doing that, you can send
me a check or money order for the amount of purchase. Checks
will take at least 7 working days to clear before I can process
your order. Make all checks or money orders out to (Donald
Harper). Send checks or money orders to: Donald Harper, 922
Redway, Houston, TX 77062. For credit card or electronic
check purchase, click on the appropriate (Buy Now) buttons
below.
For U.S purchase | For Canada purchase | For other countrys
| To return to home page: Click Here |
 | |  | |  | |  | |  | |  | |  | |  |