O2 Sensor Enhancers | Hy-Tronics
Module | PWM |  Hydro*Star
Electronics
The Hydro*Star Hy-Tronics is the electronics needed with the use of
the Hydro*Star Generator or system. It can also be used as electronics
for hydrogen generators in general. There are many hydrogen
generators that need PWMs (Pulse wave modulators) to function
properly. You can use this Hy-tronics module to accomplish this. This
along with O2 Sensor Enhancers and the incorporation of a water
vapor injector such as the UltraMist can increase your mileage
substantially! Click here to check out the UltraMist Vapor Injector.

If you have not checked out the Hydro*Star System, please

"Click Here"
Excellence ... No Doubt About It!

This Unit Controls Your PWMs (electrodes), Coil, Water Pump, and Gauge LED's!
This is an excellent replacement for the Hy-Tronics Module in the "Run Your Car On Water" manual
many people have purchased but, there is one major difference!

OURS WORKS, THEIR'S DID NOT!
Below, are a photos of the Controller's circuits and the 4 Mosfet Driver
Casings.
Many people have purchased the "Run Your
Car On Water" manual, how to build a
hydrogen generator, and, as I did, found out
that the "Hy-tronics Module" in this manual
just did not perform as their manual had
suggested!

We've totally re-designed the circuitry and
have added a second enclosure to house the
50 Amp Mosfet Driver Transistors complete,
with cooling fans!  

Our works, their's did not!
The 30 Amp Mosfet Driver has been completely tested on generators
requiring up to 45 Amps and it probably will supply 50 Amps!
The tests above were taken with our new 4 Mosfet Driver
hooked up to a cell drawing 53.2 Amps of current! This
picture was taken over an hour after beginning this test!
Warranty
The Hy-tronics Module, which is the Hydro*Star Hy-Tronics of the Hydro*Star System, is
warranted for parts and labor for 60 days from date of delivery. If you do not connect the
Hydro*Star Hy-Tronics (PWM) as outlined in the instruction that come with the units, you
could burn the system up and void your warranty. More information about your warranty will
be delivered with your order.

Please Allow Three to Four Weeks For Delivery!

Your investment for the Hy-tonics Module is $700.0 plus shipping and handling. It includes the PWM Controller and the
30Amp Mosfet Driver as seen above. This will completely control your Hydro*Star electrodes, coil, Throttle Pot, and Water
Pump as well as most Hydrogen Generators.
You can see the indicator LED lights below of the front panel of the PWM Controller. All instructions are included as well as
technical support. My phone number is: 281-670-7924 and my e-mail address is: admin@wam-a-bam.com
For United States
Residents Only
For Canada Residents Only
For All Other Countries
Most cars today are computer controlled. These computer controlled engines have O2 (oxygen)
sensors on the exhaust system to measure the exhaust gases to see if the gases are too lean or rich. If
the gases are too rich, then the computer will cut back on the fuel going to the fuel injection system. If
the gases are too lean, then the computer will dump more gas or fuel into the fuel injection system.
When you place a hydrogen generator, like the Hydro*Star System is, then the gases from the exhaust
will read too lean and the computer will want to increase the amount of fuel going into the engine. This
will defeat out purpose as we are trying to increase miles per gallon not reduce it. So, the O2 sensor
enhancer was born. This is also known as a EFIE (electronic fuel injection enhancer). To get all the
information on the EFIE (O2 sensor enhancer) click below.

                                                                Click Here  
Above is the PWM Controllers Box. Below is the
circuits and components in side the PWM Controllers
Box. Also shown here is the rear of the PWM
Controllers Box.
Above is a photo of the PWM Controllers Box on your
left and photo of the 50 Amp Mosfet Driver Transistors
Box on your right. Both are included in the purchase
price.
Above you can see the open box, showing the
components of the 50 Amp Mosfet Driver. Below is the
completed driver box.
Above is the front and rear of the PWM Controller's Box
Rear View of 30 Amp Mosfet Driver
Rear View of 50 Amp
Mosfet Driver
Electronics inside of 30
Amp Mosfet Driver
Be sure to get your free copy of the Hydro*Star Manual (Run
Your Car On Water). Click the FREE button below to download
your manual.